Kontroller mppt, tuulikule ja päiksepaneelidele

  • Eseme ID: 141356246
  • Jaga
1/1

Kontroller mppt, tuulikule ja päiksepaneelidele

Eseme ID: 141356246 Seisukord: kasutatud
Oksjon on lõppenud
Oksjon on lõppenud
Lõpphind: 57.50 EUR
Pikenev lõpp: 5 minutit
Algusaeg: E 13.07.2020 21:42:16
Lõpuaeg: E 10.08.2020 21:42:16
Vaadatud: 730
Viimati pakkus: kallem53
Koeravere, Lääne-Virumaa, Eesti
1
Seisukord: kasutatud
Asukoht: Koeravere, Lääne-Virumaa, Eesti
Kogus: 1
Transport:
SmartPOST: al. 2.99 EUR (S)
Omniva: al. 3.98 EUR (M)
DPD Pickup pakiautomaat/-pood 2.85 EUR (M)
Järeletulemisega
Maksmine: pangaülekandega, sularahas, deposiidikandega, Osta.ee e-konto ülekandega
Müüja: kaarelra100% / 302 / Vaata müüja teisi esemeid

Kasutatud veebruarist juuli alguseni. Vahetasin võimsama vastu välja, kuna lisasin paneele juurde ja ei näinud mõtet kahte kontrollerit ühte süsteemi panna. Ise jäin asjaga muidu väga rahule ja minu 3x325w paneelidest parima ilmaga laadis 36a ehk 960w. Tuulik mul oli selle seadmega 400w ja sain oma pooleldi puude ja põldude vahel välja 270w. 

Asi on 24v süsteemile ja väga lihtne paigaldada ja tootmist reaalajas jälgida.

Kõva tuulega või täis akuga pidurdab tuuliku läbi reostaadi, mis ei lõhu tuulikut ja lõpetab laadimise, kui aku täis. Täpsem info allpool.

Saab eraldi seadistada 2 väljavõtte terminali ajaliselt ja pinge põhiselt tarbijale. Nt. Valgusti, radikas...


Highlight:

1. Battery charge and discharge intelligent control

2. You can set the charge and discharge time

3. With serial communication function, real-time monitoring of the working status of the relay through the serial port

4. Additional signal output, when the relay to meet the conditions, the output high, you can control other equipment.

5. A key emergency stop function (STOP button), with reverse protection, reverse does not burn.

 

Operating mode:

Voltage upper limit: UL1, voltage lower limit nL1, the voltage upper limit is greater than the voltage lower limit (UL1> nL1)

U-1: Charging measurement: When the measured voltage is lower than the lower limit voltage, the relay pulls above, the upper limit voltage, the relay is disconnected.

U-2: charge measurement time control: set the charging time (OP), when the measured voltage is lower than the lower limit voltage, the relay pull, and then start the countdown OP time, the end of the timer, the relay off, when the measured voltage is higher than the upper limit voltage, The relay is disconnected.

U-3: Discharge detection: When the measured voltage is lower than the lower limit voltage, the relay is off, above the upper limit voltage, the relay pulls

U-4: discharge detection time control: set the discharge time (OP), when the measured voltage is higher than the upper limit voltage, the relay pull, and then start the countdown OP time, the end of the timer, the relay off, when the measured voltage below the lower limit voltage, The relay is disconnected

U-5: voltage in the range, the relay pull: when the measured voltage between the upper and lower limits, the relay pull, the other circumstances open

U-6: voltage outside the interval, the relay pull: the measured voltage below the lower limit voltage or higher than the upper limit voltage, the relay pull, the other case the relay is off.

 

Product parameters:

1: Power supply voltage: DC6--40V, voltage detection range DC 0--60V, suitable for less than 60V of the various batteries, voltage measurement error +/- 0.1V.

2: charge and discharge time (OP) range: 0 - 999 minutes.

How do I set parameters?

1. First, according to their needs, to determine the requirements of the work model

2. According to the working mode of the relay, in the main interface (when the module is powered on, it will flash the current mode of operation, the default U-1 mode, and then enter the main interface) press the SET button for 2 seconds and then release, enter the selection Mode interface, UP, DOWN button to select the mode to be set (U-1 ~ U-6)

3. After selecting the mode, assume that we have selected the U-1 mode and press the SET button to set the corresponding parameter. The parameter to be set will flash (UL1 voltage upper limit, nL1 voltage lower limit, OP conduction time), press UP, DOWN Key to increase or decrease, you can always press the key to quickly increase or decrease, press the SET button to set the current mode of the next parameter, the process above

4. Set the parameters, and then press the SET button for 2 seconds to release, the current setting mode will flash, and then return to the main interface, set the parameters of success

5. In the main interface, press the DOWN key to achieve voltage and time switching.

Mode selection interface: press the SET button for a long time to enter the mode selection interface, set the finished, a long time press the SET button and then release the exit mode selection interface, back to the main interface.

 

Additional features:

1. Data upload: through the serial port to achieve data upload, interval 1s upload a voltage and run time, easy to post-data analysis

2. Serial port settings parameters: You can set the mode and parameters through the serial port, more convenient

3. An extra signal output, when the relay to meet the conditions, the output high, the other output low.

Serial port control (TTL level communication)

Communication standard:

The baud rate is 115200 bps

Data bits: 8

Stop bit: 1

Check digit: none

Flow control: none

Serial command:

"U-1": Operating mode (range U-1 to U-6)

"000": 0 - does not enable timing function, non-0 - enable timing function (range 001 to 999)

"Dw02.9": Set the lower limit voltage

"Up10.1": set the upper limit voltage (range 00.0V ~ 99.9V)

"Get": Get the current settings

"On": Allows the relay to turn on

"Off": Always turn off the relay

"Start": start uploading data

"Stop": stop uploading data

 

The above command can be any combination of two, need to be separated by commas

Such as: "dw02.9, up10.1" set the lower limit voltage 02.9V upper limit voltage 10.1V

 

Upload Status: Test Voltage + On Time + Status

"00.0V, 00: 00: 00, OP/r/n"

00.0V: Measured voltage

00:00:00: Relay on time

Status: OP relay on, CL relay off

 

STOP key function expansion:

Relay enable mode:

1. ON: OP conduction time, the relay allows conduction

2. OFF: The relay is disabled and is always off

Press the STOP button on the main interface to switch between ON and OFF, the current status will flash, and then return to the main interface. (This function is an emergency stop function, a key to disconnect the relay)

Sleep mode:

1. C-P sleep mode: within five minutes, without any operation, the digital tube automatically shut down the display, the program normal operation

2. O-d normal mode: digital tube is always open display

Press and hold the STOP button for 2 seconds to release, to achieve C-P and O-d state of the switch, the current state will flash, and then return to the main interface.

01_副本0405030602

Küsimused müüjale

Ainult vastatud küsimused on kõigile nähtavad.

  • Invertori voimsus.?

    Tegemist on laadimis kontrolleriga 1000w paneele ja 600w tuulikut, mis annab kogu toodetud energia akudesse. Inverter eraldi seade. See ei ole inverter!

  • Eksikombel tuli kirjeldusse minu teise toote kirjeldus. Lisan siia selle kontrolleri tootja info. 1) This controller, being a high-performance wind-solar hybrid controller, can control wind generators and solar panels to charge or discharge the storage batteries at the same time; when charging, it adopts high-resolution PWM mode to charge the storage batteries via voltage and current limiting, which can effectively prolong the storage batteries’ service life. 2) The controller is provided with an accurate rotating speed measuring and controlling module, so it can check the wind generator rotating speed in real time, and also can realize over-speed brake according to the set upper limit of safe rotating speed. 3) The controller is provided with two-channel DC output interfaces, and each channel has a maximum output current 10A; for each channel, the user can independently set three kinds of different output modes, namely, light-controlled on/off, light-controlled on/time-controlled off, and normally open. 4) The controller is provided with MPPT (maximum power point tracking) function. Via advanced algorithm, It can automatically search the maximum power point to realize the maximum conversion from wind energy to electrical energy. Through test, compared with traditional controllers, this controller can improve the charging efficiency by more than two times at maximum. 5) The controller is provided with a customized LCD, so the user can easily check and set the status of controller via the human-computer interaction interface: The items which can be checked: storage battery voltage, wind generator rotating speed, wind generator voltage, wind generator current, wind generator power, photocell voltage, photocell current, photocell power, the first channel output mode, the first channel output turn-off time, the second channel output mode, the second channel output turn-off time, light-controlled on voltage point, light-controlled off voltage point, daytime or nighttime indicator, storage battery status, load status, as well as the status of faults like over-voltage, under-voltage, over-load, and short-circuit. The items which can be set: the first channel output mode, the first channel output turn-off time, the second channel output mode, the second channel output turn-off time, light-controlled on voltage point, and light-controlled off voltage point. 6) The controller is provided with a unique solar charging circuit, with a small loss and heat, which is of open-circuit unloading mode, so as to effectively prolong the solar cell’s service life. 7) Complete safety protection functions, including: >> Solar panel reverse charging prevention protection >> Solar panel reverse connection prevention protection >> Solar panel current-limiting protection >> Storage battery over-charging, over-discharging protection >> Storage battery open-circuit protection >> Storage battery reverse connection prevention protection >> Overload, short-circuit protection >> Wind generator current-limiting protection >> Wind generator over-speed protection >> Automatic and manual brake protection of wind generator >> Controller temperature monitoring, over-heat protection >> Load over-voltage protection Note: Except for storage battery reverse connection prevention protection, other protections above won’t damage the components. 8) The controller casing made of high-quality aluminum alloy is well designed, and has an attractive appearance and a good heat dissipation performance. 9) The controller is manufactured with strict production process and high-quality industrial components, so it can run reliably for a long time under cold, high-temperature, or humid environment.

    Vabandused veelkord segaduse pärast. Märkasin seda alles, kui pakkumine tehtud ja ei saa enam muuta.

  • 5 2